Board and batten siding is the perfect style for anyone looking to add some traditional charm to their home. This kind of siding can be installed on any exterior wall, but it looks great when used as an accent on a front porch or along the side of a garage . The best part about this type of siding is that you only need two materials – wood boards and thin strips of trim known as battens. Go through Architect write for us to know more about Board and batten siding
Do you know there are two styles of board and batten siding? The first is known as horizontal, which features boards running vertically on the side of a building. This type is often used for exterior walls where people come into contact with the space – like in an office or restaurant. Vertical siding can be used to create a country look by using wider planks instead of thin strips. Those who want something more modern should consider installing vertical boards and batten along portions of their home, such as around windows or doors.
The easiest way to install this type of wood-based siding is to attach it directly onto your house’s existing material with nails or screws (depending on what kind you buy). It’s also possible to install it over existing siding.
The first step is selecting the right material for your project, and this will depend on what type of wood you plan to use (e.g., pine or oak) as well as how much money you want to spend. The next big decision is deciding if you’re going with a horizontal layout like those pictured below, vertical boards that are aligned horizontally along the side of your house, or both types in different areas depending on what suits your taste best.
Steps for Installing Board and Batten siding
-
Materials needed (wood type, screws or nails)
-
Selecting the right material (vertical board alignment vs horizontal board alignment)
-
Decide if installing on an incline or flat surface:
If you’re on a slope then choose vertical boards over horizontal ones so that water doesn’t get behind them. Flat surfaces are better suited to horizontally aligned boards because they resemble shiplap siding more closely. A good rule is when looking at your house’s exterior from ground level, both types should cover about half of its length in order to look well proportioned and balanced. For example, in a two story home with a first floor that is 30 feet by 20 feet, the boards should be installed to cover about 15 and 12 feet respectively.
-
Selecting the right height
–Installing on an incline or flat surface: if you’re installing boards diagonally across from each other (horizontal board higher than vertical) then install it at 45 degree angle in order for water not to get behind them; If they are perpendicular then do so at 90 degrees – this will save space because there will only need one row of screws rather than two rows)
-Vertical alignment as opposed to horizontal: when looking up at your home, both types should cover about half of its length in order to look well proportioned and balanced. For example , if your home is 30 feet long, then the horizontal board should cover about 15 feet and the vertical boards should cover about 12.
-
Determining how many screws to use:
The average person will need around 400 wood screws per 1000 square foot of siding material for installation)
-Mixing materials with different colors or textures: Wood shingles are often mixed in order to break up monotony and provide texture but they can be difficult because you have to create a new joint at every row which leaves slight gaps; Most people would recommend installing only one type across an entire side of a house (with variation between corners/doorways).
Board and batten siders typically measure from two inches by six inches wide
-
Batten siding installation:
-Screws are installed vertically so that they align with the battens.
-Battens should be positioned at least 12 inches apart and no more than 18 inches on center; This allows for a maximum of two screws per board (and four nails).
-Start by using your measuring tape to find out how much space you need between boards before installing, which will help determine where to put the first row. If you have an even number of vertical battens, use tough measurements from both ends in order to get perfect spacing .
For instance : if your house is 30 feet long then measure 20 feet on one side and 25 feet on the other)
-
Board Material Choices :
-One option is to use a composite material like DensDeck.
-Another option is wood decking, which has the appearance of an unfinished wooden board and batten siding installation with either screws or nails.
-You can also choose a wide variety of vinyl boards for your installation that look very similar in style but offer different benefits (for example: durability).
Board Types: Tongue and Groove Board & Batten Siding Installation vs Nail Down Board & Batten Siding Installation?
Tongue and groove board and batten siding installation looks by far better than nail down when installed on both walls because it offers more protection against water damage . This type requires prepping the wall surface , durability, maintenance).
-
Fitting the Boards :
-Measure your house in sections so you can calculate how many boards are needed.
-Lay out one row of boards and then measure from both ends to make sure they’re evenly spaced before inserting them into the wall studs or siding clips.
Make sure you leave a small gap between rows when installing board and batten for added ventilation.